Engineering beam pattern design throw more light on road evenly at appropriate angle without foggy light. Xenon white light reflect road paint/signs better to show clearer road situation during night driving. 270 degree low beam angle with cut-off line, will not dazzle oncoming traffic.
All-in-one heat conduction+high speed mute fan system keep the light bulb in appropriate working temperature. Built-in constant current CPU, instant full brightness without start-up relay.
It can directly replace the traditional tungsten bulb of the original car; --The LED has high luminous purity, no need for lampshade filtering, and the light wavelength error is within 5 nanometers --There is no delay when the LED lights up, while the traditional tungsten bulb has a delay of 0.3 seconds. -LED has low power consumption. When it reaches the same brightness of traditional bulbs, it consumes only 6% of traditional bulbs, and it also saves electricity and fuel! --It has a long life, its filament-free structure does not generate heat, and it can be used for more than 6 years under normal conditions --LED car lights can make the vehicle control circuit not easy to oxidize, with a maximum load current of 0.1A. High-power chips, ultra-thin board shape design makes the installation and fit better, the illumination is more uniform, and avoids the disadvantages of poor illumination width caused by the point light source; Our Lights suitable for use with 12-30V voltage.Our Lights has the characteristics of light diffusivity, wide-angle illumination and high lumen; --No delay in lighting, high light purity, strong color rendering and penetrating power; --Using LED light-emitting diodes, low power consumption, can better protect the car circuit; --Our LED Lights has no filament, good heat dissipation, low current, low heat generation, and the vehicle circuit is not easy to oxidize; --Super bright, can be used for a long time in the temperature range of -30? --Strong shock resistance and low temperature rise, it is a new generation of revolutionary solid-state light source. All-in-one aluminum profile as heat conduction system, 360 degree heat radiating. High speed mute fan(12000R/Min), high Air flow for faster cooling rate. No need to modify the circuit, directly replace the original traditional glass bulb, pay attention to the high temperature of the original bulb to prevent burns! When installing, refer to the product dimensions and pay attention to the size of the installation location. Carefully press and do not squeeze the LED chip to avoid damage.
The LED has positive and negative polarity, if it is not bright, turn the direction and reinstall. 2 x H7 LED headlight bulbs. 2 x H11 LED headlight bulbs.2 x H11 LED Fog Light bulbs. LED lamps are more energy and power than conventional halogen lamps. The brightness is close to the xenon lamp, but the LED lights are illuminated without delay to enhance road safety. Instantly start without strong current impact, improve battery life by more than 30%.
Fast cooling, using the most advanced, heat-dissipating structural design. The power driver adopts a wide voltage constant current mode which has a simple structure, so that the automobile can flexibly cope with various voltage unstable conditions, and has achieved the purpose of less component damage. Compared to HID ballast maintenance, The repair probability is very low which is less than 80%.Low heating temperature, The working temperature of helium can reach 800°-1000°. LED headlight has a simple structure, and the parts are less than the xenon lamp, which is lower than the xenon lamp failure rate! As a safety precaution, make sure that the car has had time to cool down properly before starting the installation process. Put the vehicle into park or make sure it is securely in gear. Be sure to turn off the ignition and remove the key. Be careful to avoid burns, especially when turning on or off the vehicles lighting. Be careful to avoid crushing or cutting the bulbs.
Also make sure to not touch the bulbs with your fingers, as this will cause blotting. Fully examine the connection of the contact points, ports and the wires as faulty connections can cause lighting problems. Make certain that the end of the bulb does not come in contact with the interior light shield of the headlight when adjusting the bulb. To avoid initiating an unpaid item claim, please pay within 7 days. We believe our items are so outstanding.
All products are quality checked. We will be happy to resolve any issues you may have in a cordial and friendly manner.
We appreciate your Postive Feedback, and will do the same in return. This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts & Accessories\Lighting & Lamps\Light Bulbs & LEDs". The seller is "auto-lightbulbs" and is located in this country: US.
This item can be shipped to United States, Canada, Mexico.